If you talk about coolrunner I underatand it but gizmo says in the yellow edit matrix glitcher v3 When you unbridge the crystal that means that you use hanna point C point in matrix V3. Quote from: rafaliyo86 on November 16, , PM. SMF spam blocked by CleanTalk.
SMF 2. SimplePortal 2. I can not say it any more clearer then to Read this carefully and ask questions if needed before you do anything. You must have good soldering skills and you must pay attention to everything you do.
This tutorial will teach you everything you need to RGH a xbox console and the tools you will need for each type of console and what you will need for each dashboard. I can not say it enough please becareful when soldering. Or making sure that it powers on and boots up normally.
Once turned off unplug it and carefully removing the dvd drive , fan shroud and the mother board from the cage. Console wont power on after RGH installed? Always make sure your soldering points are correct bridge or short can cause this issue. Cool runner not Glitching? Errors in j-runner when reading nand? Restart j-runner, double check your nand wires. I think theodor had the same issue on dashboard do to it being RGH2. Edit just tried it now here is what i got Nand Initialization Finished Comparing Spare Data found, will remove.
Warning: can't patch this Falcon type SMC! This is by no means meant to be used for an everyday RGH as its as bad if not worse than a Zephyr, however it does work and will be perfect for those who have a Xenon where they lost their DVD key or an unbanned key vault.
A 47nf 0. The debug LED should flash on for less than a second and repeat every 5 seconds. Try different values of capacitors and wires.
When you have finished programming, switch it back to NOR and then power on the Xbox. By glitching the first part CBA , we take control of the system before the fuse checks occur and can patch them out. Glitching this way will work if you set it up right, but there are actually phat xboxes that already have their own split CB boot chain which were mostly ones that had been refurbished CB , , This means that on phats we can now glitch before the fuse check and thus have an unpatchable hack just like trinity!
Thank you so much for the information! Now i need help again. Everything is set up for RGH 1, the coolrunner chip is programmed for jasper. But when i connect it to the board - there is the only bright red light on the coolrunner. But when i start the console, nothing happens. No green light on the console.
Console works fine without the coorunner and with stock nand. Also it starts green light on the console with 3v3 line out of the coolrunner ofcourse it loads nothing. The hacked.
What the problem could be? I will try RGH 1. In general, it's bad to disconnect power as the chip may try to power itself with the other ports which results in possible damage to the motherboard. Thank you, I will check the CR very closely now. It can be a bad flash to CR, you said? I hope the second one, because i can try much more things with the flasing.
Interesting thing is that if i start the consle with CR installed - no boot no green light on xbox , but if I disconect the power supply in this moment and then connect it again, console shows green light. Nothing loads and CR not trying to glitch green light on CR off , but red on. I found that it is the point B on the CR, when I solder this point on the CR, the green light on the console don't turn on.
With the others it boots. My connection to the motherboard is good on point B. May be to inspect the CR traces from this point? EDIT: Oh my Haha, what I need point B for? If it is, i am so happy and thank you again!! But If it starts xell every single time, from the first glich signal, I don't think point B is needed for my setup.. Basically if u wanna use point b, u have to disable the crystal.. But my advice? Just dont use point b lol.. Edit: Never mind, used a different program and updated to so this doesn't matter to me right now.
Last edited: May 27, Joined: Feb 8, Messages: 33 Likes Received: 2. HassenC , May 28, Joined: Jun 15, Messages: 1 Likes Received: 0. Flawless perfect tutorial. I signed up just to say thanks. Rob Powell , Jun 15, Joined: May 15, Messages: 1 Likes Received: 0. Thansk for another great guide! So i can follow these steps to update my RGH console so is safe to update to the latest dash that came out last week? BlockABoots , Jun 26, No if you update your retail nand to the update released last week your RGH mode will no longer work.
Following this will update you to , presuming you are on a lower dash version for your RGH nand. InsaneNutter , Jun 27, Joined: Feb 28, Messages: 8 Likes Received: 0. Thanks for the post man, really helpful. I just get my rgh and wanted to ask a couple of questions, do i "need" to update the ms dashboard, i am already on kernel and i was just wondering for future updates, second can i install freestyle dash, i am currently on xexmenu, third what do i do i dont have the original nand dump and want to update my ms dash?
You dont need to update it all the time, however you will need to update when a major update is released. I do the major update at the end of each year and have managed not to update until the same time next year. Usually when you need to update its to support new hardware or features, e. Updates released throughout the year are usually very minor, e. So basically with Dash launch installed if a game doesn't work thats when you need to update.
0コメント